Quantity: 1, Year: 1999, 120 spindles.

Quantity: 1, Year: End of 2017, Type: VTS-05-0-F / VTS-05-0-C-F, Series: 8.02
Configuration
Number of spindles: 160, Number of sections: 20, Spindle gauge: 445 mm, Balloon limiters: without, High energy saving spindle E-260
Overall dimensions
Overall length: approx. 39.77 m, Overall width: approx. 1.50 m, Overall height: approx. 2.69 m
Technological data
Material: 100% PP, Range of counts: dtex 1200 – dtex 3800
Range of twist:Up-twisting: 40 – 710 t/m, Cabling: 20 – 355 t/m, Twist direction: S + Z
Untwisted yarn (feed packages)
Package type: cylindrical feed packages
Traverse: 10″ (254 mm), Tube length: 290 mm, Inside diameter of tube: 73 mm, Maximum outside diameter: 260 mm
Net yarn weight (approx., depending on yarn quality and package density): 5.0 kg
Twisted yarn (take-up)
Package type: cylindrical cross-wound bobbins
Traverse: 10″ (254 mm), Tube length: 290 mm, Inside diameter of tube: 73 mm
Maximum outside diameter (approx.): 350 mm
Main drive
Driven by two short-circuit squirrel-cage induction motors (one motor per machine side) with frequency inverter
Output: 2 × 37 kW, Voltage: 220/380 V, 3 phases, 50 cycles (to be confirmed in case of order)
Full motor capacity achievable if installation height does not exceed 1000 m above sea level and ambient temperature does not exceed 40°C
Electrical control
Electrical control located in the switch gear cabinet
Reversion of twist direction from S to Z manually
Drive connected via intermediate drive onto two main drive shafts, located in front of the spindles for easy access
Spindle speed controlled by frequency inverter
Terminal displaying spindle revolution, delivery speed, turns per metre and crossing angle
Spindle drive
Individual spindle drive by endless tape with 180° contact to spindle whirl, easily exchangeable
Tape tension released when spindle is stopped
No mechanical friction between tape and drive pulley due to air cushion
Gear section
One individual gear per side
Gear drive for adjusting: Turns per metre
Take-up tension (pre-take-up), Angle of crossing of take-up packages
Special cam-driven traverse motion for high-speed take-up, including anti-patterning device
Volkmann spindle (two-for-one and cabling spindle)
Maintenance-free spindle, rigidly fixed to spindle rail, with two yarn channels:
One for two-for-one twisting, One for direct cabling
Spindle rotor statically and dynamically balanced
Reserve discs with anti-wrap collar to avoid yarn wraps around the whirl in case of ends down
Stationary protection pot held by permanent magnets with tension device
Separators between individual spindles
Machine equipped with Volcojet
Machine without balloon limiters
Take-up
Adjustable pre-take-up per machine side to vary take-up tension and package density
Adjusting range: 60%, Traversing thread guides, self-threading, fixed on traverse rod
Drive of packages by friction rollers
Pivotable balloon thread guides with enclosed ceramic eyelet, height adjustable per section
Device for producing hard and soft packages
Cradle
Swivelling, spindleless four-bar cradle with special pressuring device to ensure uniform density throughout package diameter
Centering discs for take-up tubes, simple ball-and-socket type bearing, easily exchangeable for different tube dimensions
Machine colours
Textured paint, Principal colour: Light grey NCS S 0510-R90B
Secondary colours:Traffic grey B NCS S 7502-B, Red NCS S 1080-Y90R, Anthracite grey NCS S 8502-B

Note: Machine is professionally dismantled, packed and warehoused by Volkmann technicians. with energy reduction

Quantity: 2, Year: 1989/1990, 120 spindles, each side independent, with own gears and motor 45kW, 380V/3Ph/50Hz, feeding 10” assembling bobbins, Volcojet air threading, delivery 10” cylindrical tubes tubes, conical tubes also possible,

Quantity: 1, Year: 1991, 104 spindles, Alimentation 10”, Exit cone 10”, pneumatic threading, Blower, 380 V 50 HZ, Condition:Dismantled
This TWO FOR ONE machine work cotton, it is for course counts,

Quantity: 1, Year: 2012, mod. 05-0 type 8.02, 40 heads (20×2), feeding 10″, free ballon, can dia.350 mm., delivery 10″, pneumatic doffing and air threading device. Machine running.

Quantity: 2, Year: 2018, Type: 05-0-C-F, Design / Version (Bauart): 8.05.

Quantity: 1, Year: 2013, Spindles: 162, Guage: 230mm, Delivery 4’20, Area Needed(m): 22.5L*1W +2m Each side, Average production: 900 Kg, 10Nm-85Nm. double feeding, Intake small cone, Output 4”20. Twin pack, Feeding with 2 4’2 cone, Deliver 1 twisted. It can twist cotton yarn, spun and viscose or any type of yarn except the continuous filament yarn.
Machines are in production, in perfect condition.

Quantity: 1, Year: 1996, Type 4.21, 80 positions, Pot día 230 mm., 8″ feeding, 6″ delivery, 5°57′ conicity.

Quantity: 3, Year: 1996, Two for one twister, Bauart 5.10, General overhauled in 2018, 144 spindles, Feeding: assembling bobbins 6-7”, tubes length until 205 mm, Diameter until 175 mm, pot diameter 185 mm, Delivery: conical and cylindrical tubes, length 170mm, 6” traverse, diameter until 350 mm, 2-3 kg, bobbin lift by yarn break, air threading Volcojet, waxing device, spindle speed 2.600-5.500 tpm. Very good condition, machines have run only few years in 2 shifts, still running. MACHINES ARE PARTIALLY IN PRODUCTION.

Quantity: 1, Year: 2001, 6 inch output, 208 spindle, no malfunction.

Quantity: 14, Year: 6×2012 – 8×2013, Type: 05-0-C, Spindles: 13×160 – 1×120, Capacity in ton @ 2000 dtex and 85 tpm: 13×4.4 – 1×3.3, POT diameters for these twisters is 298 mm.
The electrical/mechanical parts like motors , gears , shafts , bearing , roller , etc are all working.
Those machines need to replace the pneumatic systems inside , 3/2 valve , central valve , pneumatic pipe, etc.
Stopped on Mill Floor.

Quantity: 3
Volkmann VTS 07 Twisting
Suitable to make soft packages by increasing the overfeeding speed and by threading the yarn.

Quantity: 1, Year: 2000, Bauart 5.70, n.176 spindles, Feeding 8″ (200 mm) from assembly winder, Maximum feed bobbin diameter 178 mm, Exit 6″ (152 mm) – conicity 4°20′, Waxing device, Pneumatic threading, Yarn reserve – soft bobbin return, Single-control spindle speed- inverter, Dual-control twist adjustment, Inverter for spindle speed adjustment, Magitex.

Quantity: 1, Year: 1998, Bauart 5.60, 160 spindles, Feeding 2×6″ with daisy device and 8″ (200 mm) from assembly winder, Maximum feed bobbin diameter 178 mm, Exit 6″ (152 mm) – conicity 4°20′, Waxing device, Pneumatic threading, Yarn reserve – soft bobbin return, Single-control spindle speed- inverter, Dual-control twist adjustment, Magitex.

Quantity: 2, Year: 2003, 144 Spindles.

Quantity: 3 , Year: 2007, mod. 6.10, 192 positions

Quantity: 1
Year: 2000
Double twist twister for spun yarn
192 spindles (8+8 spindles per section)
Informator for programming work data
Dual control (allows different twisting and speed on each side)
Possibility of dividing the machine into three groups on each side of the machine, which allows working up to three twists and three different speeds on each side of the fan.
Yarn guide movement is common by each side of the machine
1 individual rotating motor in each spindle
Start/stop button on each spindle
Electronic sensor/yarn presence probe w/ automatic spindle stop in case of breakage
Pneumatic yarn feeding
Fedding bobbin up to 10″ coming from assembly winder
Device for forming of soft packages, if desired for dyeing
Output pachages of 6 inches (152mm of wire winding)
Possibility of forming conical bobbins 4º 20; 5°57, or cylindrical bobbins as desire
Lateral reserve of yarn for weaving preparation
Automatic package lifting with blockage aplet
Top creedle with supports for empty cones or full packages
MAGITEX traveling blower with box for centralized discharge with timer
Longitudinal tape with micros for emergency stop of the machine in case of need
Inverter speed drives for electronic introduction of torsion and spindle speed
RPM 9,000 (18,000 double twist)
Minimum TPM 80
In excellent maintnance condition and functioning.
Machine lengths 21940mm
Voltage 380v.3c.50hz.
NOTE; Machine professionally dismantled, and moved to warehouse.

Quantity: 1, Year: 2001, with Nº 120 spindles , double side ( 60 each frame x 2 ) , single drive ,
feeding 10″ inch from assembly winder bobbins , tube length 270 mm. ,
basket diam. 235 mm. , delivery on cones 10 ’’ ( traverse 250mm. ) , cones length 270 mm. ,
pneumatic thread-in volcojet , inverter to speed set , Machine complete in good running condition ;

Quantity: 2, Year: 1989/1990, 120 spindles each, Feeding & delivery 10″, Tubes 280mm, Gears for different turns/m each side, Each machine fit 2 container.

VOLKMANN 2×1 Twister
Quantity: 1, Year: 1985, mod.VTS-06S , 40 spindles (20×2), feeding tube 285 mm. x dia.70 mm., can dia.225 mm., gauge 320 mm., output tube 280 mm 4°20, pneumatic air threading device.

OMM Precision Assembly winder
Quantity: 1, Year: 2009, mod.D06 BPN, 6 heads, independent heads, (4) tube 10″ and (2) tube 8″, lateral creel, 6 ends

Quantity: 1, Year: 1985, No of Spindle: 96, Pot Dia in mm: 290, Traverse in Inch: 10, Spindle Pitch in mm: 355, Motor kW: 37, Delivery Package: Cheese, Conicity: Cylindrical, Outer Pot: Available, Spindle Drive: Tangential, Stopped.

Quantity: 1, Year: 1986, Type VTS-05, 96 Spindles, Exit cone 10” – 3°30.Note: The machine is complete with software

Quantity: 1, Year : 2015 / Start up 2016, Type 05-0-C
Machine ihas less workinghours and is like new, Type 8.02, Number of spindles: 40
Output: 10“ (254mm) cylindric, max diameter 400mm, spindelpotdiameter 285mm, spindelpot high 300mm, Fabrics: Acryl, glass fibers, copper

Quantity: 1, Year: 2003, 120 positions.

Quantity: 1, Year: 2013, 160 spindles.

Quantity: 6
3x Year: 2021, 176 spindles, ⁠Pot Diameter 275mm, ⁠Travears: 250 mm, ⁠Length of machine: 43.15mm, ⁠Gap between 2 pots: 450mm.
3x Year: 2012, 176 spindles.
Very good condition.